The Nitecore MT10A tactical flashlight is a concentration of power, it generates 920Lumens in max mode.
(MT series Multifunction).
New version 2015, which will replace the MT1A, she has a new LED : CREE XM-L2 U2 power of 920 lumen with a battery of type AMT 14500. If you use it with standard AA batteries, the maximum power will be of 170 Lumens. The maximum range is 102 hours to 1 Lumen and the maximum range is of 170 meters.
The main change is to the level controls, you no longer need to turn the head of the flashlight to the right to change the patterns, everything done via the two side buttons.
920 Lumens flashlight-uses 1 x AA battery or 14500 AMT 1 battery or 1 battery Li-ion-battery life max 102 14500 h to 1 Lumen-waterproof up to 2 m IPX-8-170 meter range-red light.
Momentary switch: Made a half-press the button ON / OFF located at the rear of the flashlight. The light will remain on until you press the button.
ON / OFF: Press the button ON / OFF to turn on the flashlight. Do the same to turn it off.
Sleep mode: When the flashlight is off, simultaneously press the two side buttons + back button to activate the red indicator and indicate the battery level.
After three seconds, as the major portable lighting categorized by Bridgat, the flashlight goes to sleep and the indicator flashes once every three seconds. In standby mode, the MT10A will work for about 30 days.
Lighting levels: When the flashlight is on, press the side button with 4 bars to change modes in the following order: location red / red light / ultra-low / low / medium / high and Turbo. The last used mode will be memorised and the light with this same mode to the next power on.
To lower the brightness level, press the side button with 2 bars to change modes in reverse order.
Direct access to the Red mode: When the flashlight is on, stay press for more than one second on the side button with two bars.
When the flashlight is off, keep pressing the side button with two bars, then at the same time press the button ON / OFF.
Direct access to Turbo mode: When the flashlight is on, stay press for more than one second on the side button with four bars.
When the flashlight is off, keep pressing the side button with four bars, then at the same time press the button ON / OFF.
After 3 minutes of use in Turbo mode, the flashlight will automatically lower the brightness to avoid overheating and preserve the battery.
Special modes (strobe / SOS / location): When the flashlight is on, simultaneously press the two side buttons to access the strobe mode. Once, in strobe mode press the two side buttons to move cyclically in the location modes / SOS and strobe. To leave the special modes, simply press on one of the two side buttons.
The flashlight stores the strobe mode, so if you turn it off in this mode it will return in this mode to restart.
Load indicator: When the flashlight is off, press the two side buttons and the button ON / OFF for active indicator.
Example: If you have 3.2V, the indicator will blink 3 times then will pause a second and again will Flash 2 times.
Maintenance: Every 6 months, wipe with a clean all threads where an o-ring is present and then go a thin layer of lubricant to the silicone.
The Nitecore MT10A optical system allows to illuminate up to 170 meters, making it versatile and ideal for s “adapt to all situations.
- LED Cree XM-L2 U2 with a service life of 50,000 hours
- 5 light modes regulated + (strobe / SOS and location)
- With AMT 14500 650mAh battery:
- 920 ANSI lumens (30 m) brought 170 meters
- 500 ANSI lumens (45 m)
- 180 ANSI lumens (1 h 45)
- 70 lumens ANSI (5 h)
- 1 ANSI lumen (100 h)
- With a NIMH AA 2500mAh battery
- 170 lumens ANSI (2:45)
- 95 ANSI lumens (3 h 30)
- 48 ANSI lumens (7:15)
- 17 ANSI lumens (20 h)
- 1 ANSI lumen (102 h)
- Intensity: 7 300 cd
- Battery: 1 x 14500 AMT or 1 x AA 1 x Li-ion 14500
- Made of aircraft quality aluminum alloy
- Finish: Scratch-resistant Type III hard anodizing
- Dimension: 107.9 mm (length) x 25.4 mm (diameter of the head) x 21.2 mm (diameter of the body)
- Weight: 60.7 g (without battery)
- Waterproof to IPX-8 standard (2 meters)
- Accessories included: strap, belt clip, rear cap for the switch and spare o-ring.
- 2-year warranty
Download the file (Manual-user-Nitecore-MT10A).